|
A. The
pen's capsules are moulded on an Automatic moulding machine Where the
temperature and pressure control is precisely controlled by a proper Instrument
controls.
The Plastic Powder which is used for the capsule is polypropylene or
polysteren
confirming to the IS : 2267 - 1972. The design of the mould for any
specific recorder
is 100% identical to the original pen of the recorder manufacturer
We stand guarantee that, every
capsule will be 100 % re-throfit for the particular
model and type of the recorder and
will have a smooth finish and will be free from
any defects.
B. The Cartridge ( ink absorbent material ) which is used for
containing or retaining the
ink, comes in two types. 1. For the Cubical Capsule : we use the
high capacity
absorbent cotton wool felt of the best quality available in the market.
2. For the Cylindrical capsule : we use cellulose acetate polyster fibres
(IS : 10562-1983)
C. The tips which are used with our products are of two
types and have the advantages in
their own properties and are used for the appropriate duties depending on the
design
of the recorder, to give the best results. For your reference we give a
comparison of
the two types of tips which are being used, Micro tips & Fibre tips.
|
Fibre Tips :
|
Micro Tips :
|
|
1. Indigenous
|
1. Imported (JAPANESE)
|
|
2. O.D. is
2 mm
|
2. O.D. is 0.8 mm
|
|
3. Made of
chemically treated Cellulose
acetate polyester Fibre, hardened.
|
3. Nylon fibres embeded in
a solid nylon sleeve. |
|
4. Initial
line width is 0.3 mm and over a
period use the tip gets blunt and line
width can becomes as wide as 0.85 mm.
|
4. The line width is very sharp (0.2mm)
and remains the same till the end if
the contact pressure is not more than 10
grams. |
|
5. Has a very
good capillary action and can
write well with only 3 grams contact
pressure and 00 mm / sec pen speed.
|
5. Has slow cappillary action and can
write well with a 10 gm. contact
pressure and 50 mm / s pen speed. |
|
6. Ink flow
is fast hence the writting length is
less
For a given volume of ink.
|
6. Ink flow is slow hence the writing length
is more, for a given volume of ink. |
The specific conditions in which our pens have been tested are as follows
:-
|
1. Pen Tip Pressure
|
6.0 grams.`
|
| 2.
Room Tempreture
|
21 o C
|
| 3. Relative Humidity
|
67 %
|
| 4. Line width
|
0.31 to 0.33 mm.
|
| 5. Pen speed
|
100 mm / Sec (Maximum)
|
| 6. Chart speed
|
50 mm / Min (Maximum)
|
We are the O.E.M. Supplier for some of the Indian Recorder Manufactures.
The Shelf Life
: We guarantee our products for 6 months but in a proper A.C.
Store it
can be for One
year also.
As we fill up the measured quantity of ink, the chances of ink oozing out from
the joints at
high ambient temperature,
are very little, but in some cases if the ink-settling time is not
given
adequately, it may leak. To avoid that, please let us have
the delivery
time of six to eight
weeks.
For the better writing of our pens we recommend the chart Paper should be of I.S.
5947 - 1970
with the following specifications :-
|
1. Gramage ( g / m 2
)
|
= 47.81 |
|
2.
Tensile strength kg / m 2
15mm
|
= N.D. 2.74
C.D. 1.90
|
|
3. Cobb Test ( g / m 2 )
|
= Felt side 16.26
Wire side 19.28
|
|
4. Thickness in inches
|
= 0.0024
|
|
5. Smoothness ML / Min
|
= More than 300 ML / Min....
|
|
6. Above specifications at
|
= 27 o C + 1 o C.
65 RH + 2%
|
We hope that all the given specifications will fulfill your requirements.
If you have any
more queries,
you are always welcome to write us.
|
